View T260XW02-VK_7698252.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 1/28 no reproduction and redistribution allowed free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 2/28 no reproduction and redistribution allowed document version: 0.0 date: 2007/1/9 product specifications 26.0 wxga color tft-lcd module model name: t260xw02 vk () preliminary specifications (*) final specifications free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 3/28 no reproduction and redistribution allowed contents no item cover contents record of revisions 1 general description 2 absolution maximum ratings 3 electrical specifications 3-1 electrical characteristics 3-2 interface connections 3-3 backlight connector pin configuration 3-4 signal timing specifications 3-5 signal timing waveforms 3-6 color input data reference 3-7 power sequence for lcd 4 optical specifications 5 mechanical characteristics 6 reliability 7 international standards 7-1 safety 7-2 emc 7-3 green 7-4 emi 8 packing 9 precautions free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 4/28 no reproduction and redistribution allowed record of revision version date no old description new description remark 0.0 2007/1/9 1st release free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 5/28 no reproduction and redistribution allowed 1. general description this specification applies to the 26.0 inch color tft-lcd module t260xw02. this lcd module has a tft active matrix type liquid crystal panel 1366x768 pixels, and diagonal size of 26.0 inch. this module supports 1366x768 xga-wide mode (non-interlace). each pixel is divided into red, green and blue sub-pixels or dots which are arranged in vertical stripes. gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot. the t260xw02 has been designed to apply the 8-bit 1 channel lvds interface method. it is intended to support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very important. * general information items specification unit note active screen size 26.0 inches display area 575.769 (h) x 323.712(v) mm pixel pitch 0.4215 mm outline dimension 626.0 (h) x 373.0 (v) x 46.2(d) mm with inverter driver element a-si tft active matrix display colors 16.7m colors number of pixels 1366 x 768 pixel pixel arrangement rgb vertical stripe display mode normally black bl structure 6 u-lamps surface treatment ag, 3h rohs rohs compliance free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 6/28 no reproduction and redistribution allowed 2. absolute maximum ratings the following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. item symbol min max unit conditions logic/lcd drive voltage vcc -0.3 13.5 [volt] note 1 input voltage of setup pin vin -0.3 3.5 [volt] note 1 input voltage of lvds signal v -0.3 2.5 [volt] note 1 blu input voltage vddb -0.3 27 [volt] note 1 blu brightness control voltage vblon -0.3 5 [volt] note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 10 90 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 10 90 [%rh] note 2 panel surface temperature - 65 [ o c] note 2 pwm duty cycle 92% note 1: duration: 50 msec. note 2 : maximum wet-bulb should be 39 and no condensation. note 3 : limited by inverter. the relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperature must not exceed 39 . free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 7/28 no reproduction and redistribution allowed 3. electrical specification the t260xw02 requires two power inputs. one is employed to power the lcd electronics and to drive the tft array and liquid crystal. the second input power for the blu is to power inverter. 3-1 electrical characteristics values parameter min typ max unit notes lcd: power supply input voltage vcc 10.8 12 13.2 vdc 1 power supply input current icc - 0.5 - a 2 power consumption pc - 6 - watt 2 inrush current i rush - - 3 apeak 3 differential input high threshold voltage vth - - +100 mv 4 differential input low threshold voltage vtl -100 - - mv 4 lvds interface common input voltage vcim 0.6 1.2 1.8 v input high threshold voltage vih (high) 2 - - vdc cmos interface input low threshold voltage vil (low) - - 0.8 vdc backlight power consumption pddb 62 66 70 watt 90% pwm dimming life time 50,000 - - hours note: 1. the ripple voltage should be controlled under 10% of v cc 2. vcc=12.0v, = v f 60hz, fclk=80mhz , 25 , test pattern : white pattern 3. measurement condition : trush = 470 us 10% 90% vcc gnd free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 8/28 no reproduction and redistribution allowed 4. vcim = 1.2v vth vcim vtl 0v 5. the performance of the lamp in lcm, for example life time or brightness, is extremely influenced by the characteristics of the dc-ac inverter. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. when you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. when you confirm it, the lcd assembly should be operated in the same condition as installed in your instrument. 6. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, tft-lcd module have a low luminance and the inverter has abnormal action because leakage current occurs between lamp wire and conducting tape. 7. the relative humidity must not exceed 80% non-condensing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperature must not exceed 39 . when operate at low temperatures, the brightness of ccfl will drop and the life time of ccfl will be reduced. free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 9/28 no reproduction and redistribution allowed 3-2 interface connections (12v 1ch lvds) - lcd connector fi-re41s-hf (jae) pin no. description pin no. description 1 vdd(12v) 21 rxclk+ 2 vdd 22 gnd 3 vdd 23 rx3- 4 vdd 24 rx3+ 5 vdd 25 gnd 6 gnd 26 nc 7 gnd 27 nc 8 gnd 28 nc 9 gnd 29 reserved 10 gnd 30 reserved 11 rx0- 31 nc 12 rx0+ 32 nc 13 gnd 33 nc 14 rx1- 34 nc 15 rx1+ 35 nc 16 gnd 36 nc 17 rx2- 37 nc 18 rx2+ 38 nc 19 gnd 39 reserved 20 rxclk- 40 reserved 41 reserved note: all gnd (ground) pins should be connected together and should also be connected to the lcd s metal frame. all vcc (power input) pins should be connected together. block diagram free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 10/28 no reproduction and redistribution allowed 3-3 backlight connector pin configuration 3-3-1. electrical specification item symbol condition min typ max unit note input voltage v ddb --- 23.0 24 26.4 vdc input current (stable condition) i ddb vddb=24v 2.61 2.75 2.89 adc 1 input power (stable condition) p ddb vddb=24v 62 66 70 w 1 on vddb=24v 2 --- 5 adc 1 on/off control voltage v blon off vddb=24v 0 --- 0.8 vdc on/off control current i blon vddb=24v -1 --- 1.5 madc high vddb=24v 2 -- 5 pwm dimming control voltage v dim low vddb=24v 0 -- 0.8 vdc note1: condition : vddb=24v (ta=25 5 , turn on for 45minutes), pwm=90% 3-3-2. input specification - connector: s14b-pha-sm-14 (jst) no symbol description 1 vddb (main power) dc input 24.0 vdc 2 vddb (main power) dc input 24.0vdc 3 vddb (main power) dc input 24.0 vdc 4 vddb (main power) dc input 24.0 vdc 5 vddb (main power) dc input 24.0 vdc 6 gnd ground 7 gnd ground 8 gnd ground 9 gnd ground 10 gnd ground 11 det status operation="l", fail="open collector" 12 vblon (enable pin) on/off control signal; 3.3v:on/ 0v:off 13 nc nc 14 vdim (lcd bright) dimmer pwm (20%-90%) note: free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 11/28 no reproduction and redistribution allowed 3-3-3. backlight diagram free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 12/28 no reproduction and redistribution allowed 3-4 signal timing specifications this is the signal timing required at the input of the user connector. all of the interface signal timing should be satisfied with the following specifications for it s proper operation * timing table de only mode 1. display position is specific by the rise of de signal only. 2. horizontal display position is specified by the rising edge of 1 st dclk after the rise of 1 st de, is displayed on the left edge of the screen. 3. vertical display position is specified by the rise of de after a low level period equivalent to eight times of horizontal period. the 1 st data corresponding to one horizontal line after the rise the of 1 st de is displayed at the top line of screen. 4. if a period of de high is less than 1366 dclk or less than 768 lines, the rest of the screen displays black. 5. the display position does not fit to the screen if a period of de high and the effective data period do not synchronize with each other. signal item symbol min typ. max unit v total tv 785 810 1000 th active tdisp(v) 768 th vertical section blanking tblk(v) 17 42 232 th h total th 1414 1648 1900 tclk active tdisp(h) 1366 tclk horizontal section blanking tblk(h) 48 282 534 tclk pixel clock frequency 1/tclk 60 80 85 mhz vertical frequency frequency fv 47 60 63 hz horizontal frequency frequency fh 43 48 53 khz free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 13/28 no reproduction and redistribution allowed 3-5 signal timing waveforms t h t d i s p ( v ) t v d e r g b d a t a 7 6 8 l i n e i n v a l i d d a t a i n v a l i d d a t a 1 l i n e 2 l i n e 3 l i n e 7 6 8 l i n e 4 l i n e t c l k c l k d e r g b d a t a p i x e l 1 3 6 6 i n v a l i d d a t a p i x e l 1 p i x e l 2 p i x e l 3 p i x e l 4 p i x e l 5 p i x e l 6 p i x e l 1 3 6 6 i n v a l i d d a t a p i x e l 1 p i x e l 2 t h t d i s p ( h ) free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 14/28 no reproduction and redistribution allowed 3-6 color input data reference the brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 green green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ------- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 blue blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 15/28 no reproduction and redistribution allowed 3-7 power sequence for lcd values parameter min. typ. max. units t1 0.47 - 30 ms t2 5 - 50 ms t3 500(note 2) - - ms t4 100 - - ms t5 0.1 - 50 ms t6 0.47 - 30 ms t7 300 - - ms note 1: apply the lamp voltage within the lcd operation range. when the back-light turns on before the lcd operation or the lcd turns off before the back-light turns off, the display may momentarily become abnormal screen. note 2: a. 200ms~550ms: without turning color temperature might happen in this period b. >550ms: normal operation period, with color temperature turning free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 16/28 no reproduction and redistribution allowed 4. optical specification optical characteristics are determined after the unit has been on and stable for approximately 45 minutes in a dark environment at 25 . the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0 . fig.1 optical measurement equipment and method. values parameter symbol min. typ. max. units notes contrast ratio cr 1200 1500 1 surface luminance, white l wh 420 500 cd/ O 2 luminance variation white 9 p 1.3 3 response time gray to gray (average) t 8 ms 4,5 color coordinates r x 0.650 red r y 0.333 g x 0.300 green g y 0.590 b x 0.145 blue b y 0.055 w x 0.280 white w y typ.-0.03 0.280 typ.+0.03 color gamut ntsc 72 % viewing angle x axis, right( =0 ) r 75 89 degree x axis, left( =180 ) l 75 89 degree y axis, up( =90 ) u 75 89 degree y axis, down ( =0 ) d 75 89 degree 6 sr3 or equivalent device free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 17/28 no reproduction and redistribution allowed note : 1. contrast ratio (cr) is defined mathematically as: surface luminance of l on1 contrast ratio= surface luminance of l off1 2. surface luminance is luminance value at point 1 across the lcd surface 50cm from the surface with all pixels displaying white. from more information see fig 2. when v ddb = 24v, i ddb =2.91a, l wh =lon1. where lon1 is the luminance with all pixels displaying white at center 1 location. pwm dimming=90% 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 , l on9 ) / minimum(l on1 , l on2 , ,l on9 ) 4. response time is the time required for the display to transition from black to white(rise time, tr r ) and from white to black (decay time, tr d ). for additional information see fig3. 5. t is the response time between any two gray scale and is based on f v =60hz to optimize. 6. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig4. fig.2 luminance 1 2 3 4 5 6 7 8 h v h/6 h/2 v/2 v/6 free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 18/28 no reproduction and redistribution allowed fig.3 response time the response time is defined as the following figure and shall be measured by switching the input signal for black and white . fig.4 viewing angle tr d any brighter gray level (white) any darker gray (black) n a n c e time tr r 10% optical response 100% 90% 0 any brighter gray level (white) free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 19/28 no reproduction and redistribution allowed 5. mechanical characteristics the contents provide general mechanical characteristics for the model t260xw02. in addition the figures in the next page are detailed mechanical drawing of the lcd. horizontal 626.0mm vertical 373.0mm outline dimension depth 46.2mm(w/i inverter & shielding) horizontal 581.8mm 0.5mm bezel area vertical 328.8mm 0.5mm horizontal 575.769mm active display area vertical 323.712mm weight 4,900g (typ.) surface treatment anti-glare, 3h torque on bottom chassis user holes (min affordable value) m3: 10kgf-cm m4: 10kgf-cm (by sony screw) free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 20/28 no reproduction and redistribution allowed front view free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 21/28 no reproduction and redistribution allowed rear view free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 22/28 no reproduction and redistribution allowed 6. reliability environment test condition no test item condition 1 high temperature storage test ta=60 300h judge 2 low temperature storage test ta=-20 300h judge 3 high temperature operation test ta=50 80%rh 300h judge 4 low temperature operation test ta=-5 300h judge 5 vibration test (non-operating) wave form: random vibration level: 1.5g rms bandwidth: 10-300hz duration: x, y, z 30min each direction 6 shock test (non-operating) shock level: 50g waveform: half since wave, 11ms direction: x, y, z one time each direction 7 vibration test (with carton) wave form: random vibration level: 1.5g, bandwidth: 10~200hz duration: xyz 30min each direction 8 drop test (with carton) height: 31cm 1 corner, 3 edges, 6 surfaces (astmd4169-i) free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 23/28 no reproduction and redistribution allowed 7. international standard 7-1 safety (1) ul6500, underwriters laboratories, inc. (auo file number: e204356) standard for safety of information technology equipment including electrical business equipment. (2) can/csa c22.2 no. 950-95 third edition, canadian standards association, jan. 28, 1995 standard for safety of information technology equipment including electrical business equipment. (3) en60950: 1992+a2: 1993+a2: 1993+c3: 1995+a4: 1997+a11: 1997 iec 950: 1991+a1: 1992+a2: 1993+c3: 1995+a4:1996 iec 60065 (auo certificate number: jptuv-008549) european committee for electro technical standardization (cenelec) european standard for safety of information technology equipment including electrical business equipment. 7-2 emc a) ansi c63.4 methods of measurement of radio-noise emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. american national standards institute(ansi), 1992. b) c.i.s.p.r limits and methods of measurement of radio interface characteristics of information technology equipment. international special committee on radio interference. c) en 55022 limits and methods of measurement of radio interface characteristics of information technology equipment. european committee for electrotechnical standardization. (cenelec), 1998. 7-3 green green mark description: a) for pb free products, auo will add for identification. b) for rohs compatible products, auo will add for identification. note. the green mark will be present only when the green documents have been ready by auo internal green team. (the definition of green design follows the auo green design checklist.) 7-4 emi item min typ max unit emi level note1) -4 -6 --- db( v/m) sscg 300 ---- --- ps note 1) a) criteria: cispr22 b)signal generator : psg200-1(sony emcs) free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 24/28 no reproduction and redistribution allowed 8. packing label sample 83mm * 23mm carton label model no: t260xw02 vk au o ptronicsqty: 5 *pm100-01a1600001* made in xxxxx customer no: carton no: part no: 97.26t02.k00-m11 free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 25/28 no reproduction and redistribution allowed carton size 722(l) mm*325(w) mm*469(h) mm 5pcs modules cushion set 1pcs module/esd bag module h tape 5pcs / 1 carton free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 26/28 no reproduction and redistribution allowed specification item qty. dimension weight (kg) packing remark 1 packing box 5pcs/box 722(l)mm*325(w)mm*469(h)mm 28.4 2 pallet 1 980(l)mm*730(w)mm*120(h)mm 3 boxes per pallet 6 boxes/pallet 4 panels per pallet 30pcs/pallet 5 pallet after packing 30 980(l)mm*730(w)mm*1058(h)mm 180 .4 stretch film label corner angle pet band moisture-proof film corner angle pallet free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 27/28 no reproduction and redistribution allowed 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1 mounting precaution (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to module. and the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protective plate to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front/ rear polarizer. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possible. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2 operation precautions (1) the spike noise causes the mis-operation of circuits. it should be lower than following voltage: v= 200mv(over and under shoot voltage) (2) response time depends on the temperature. (in lower temperature, it becomes longer..) (3) brightness depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time (required time that brightness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperature change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (5) when fixed patterns are displayed for a long time, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shall be done by system manufacturers. grounding and shielding methods may be important to minimize the interface. free datasheet http://
copyright au optronics, inc. january, 2006 all rights reserved. t260xw02 vk - spec. ver0.0 28/28 no reproduction and redistribution allowed 9-3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make certain that treatment persons are connected to ground through wrist band etc. and don t touch interface pin directly. 9-4 precautions for strong light exposure strong light exposure causes degradation of polarizer and color filter. 9-5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunlight or fluorescent light. keep the temperature between 5 and 35 at normal humidity. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. 9-6 handling precautions for protection film (1) the protection film is attached to the bezel with a small masking tape. when the protection film is peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached is stored for a long time, sometimes there remains a very small amount of flue still on the bezel after the protection film is peeled off. (3) you can remove the glue easily. when the glue remains on the bezel or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. free datasheet http://

▲Up To Search▲

Price & Availability of T260XW02-VK

	To Download T260XW02-VK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .